GE three-power boxcab

GE three-power boxcab

Type and origin
Power type Electro-diesel & battery
Designer General Electric
Builder ALCO
Order number S-1690
Model 404-OEB-255
Build date 1930
Total produced 41
Specifications
AAR wheel arr. B-B
UIC class Bo'Bo'
Gauge 4 ft 8 12 in (1,435 mm)
Wheel diameter 44 in (1,100 mm)
Wheelbase 34 ft 1 in (10.4 m)
Loco weight 255,000 lb (115.7 t)
Fuel type Diesel
Prime mover Ingersoll Rand
RPM range 550 maximum
Engine type 4-stroke diesel
Displacement 942 cu in (15.4 l)
Generator GE 200 kW (270 hp) 600 V
Traction motors GE-286-B
Cylinders 1 x 6
Cylinder size 10 in (254.0 mm) bore
12 in (304.8 mm) stroke
Couplers AAR knuckle
Performance figures
Maximum speed 40 mph (64 km/h)
Power output:
  1 hour electric: 1,580 hp (1,180 kW)
Tractive effort 30,000 lbf (130 kN) @
internal power: 9 mph (14 km/h)
3rd rail power:19 mph (31 km/h)
Career
Operators New York Central
Rock Island: 1
Class prototype: DEs-2
series: DEs-3
Power class 600 V DC Third Rail
Number in class prototype: 1
series: 40
Numbers prototype: NYC 1525, later 525
series: NYC 1526–1566, RI 10000
Withdrawn 1960s, 1970s
Disposition scraped

The GE three-power boxcabs were early electro-diesel hybrid switcher locomotives. These boxcabs were termed oil battery electrics[1] to avoid the use of the German name Diesel, unpopular after World War I.[2]

History

Prototype of GE three-power-boxcab delivered as NYC #1525

The prototype of these locomotives was New York Central 1525 delivered in February 1928. This locomotive had a center-cab design. After successful testing a series of 40 locomotives [1] with boxcab carbodies were built along with the line of the ALCO boxcabs by a consortium of ALCO, General Electric, Ingersoll Rand and Electric Storage Battery. ALCO built the locomotive frame, carbody and running gear, General Electric built the generator, traction motors and controls, Ingersoll Rand provided the diesel engine and Electric Storage Battery from Philadelphia - the today's Exide, the traction batteries.

The locomotives were mainly used in city areas for switching work, where exhaust-emissions-free operation was required at spurs entering factory halls. The main batch was ordered by New York Central Railroad to be used in the New York City area operating on the West Side Line and the High Line. Some three-power boxcabs also worked Chicago, Detroit, and Boston. One locomotive was built for Rock Island, which used it for switching the LaSalle Street Station in Chicago.

Technical Description

The principle of operation was similar to that of modern hybrid locomotives, the diesel engine driving a main generator of 600 volts DC, which provided charging current to a bank of batteries which powered four traction motors, one per axle. In addition to being powered by the diesel engine, these locomotives were capable of operating as electric locomotives. Two of these locomotives were equipped to operate off of 3000 volt overhead lines, and 34 were capable of operating off of a 600 volt third rail. The locomotives were equipped with a six-cylinder four-stroke in-line engine of 300 hp (224 kW). The diesel motor was used to charge the batteries, which could not be charged by third rail power.[3] The battery consisted of 240 Exide Ironclad cells with a total capacity of 301 kWh.[4]

See also

References

  1. 1 2 "Locomotives of the New York Central System" (PDF). Railroad Magazine. 1940. Retrieved 2016-06-12.
  2. Mark Garrett (13 August 2014). Encyclopedia of Transportation: Social Science and Policy. SAGE Publications. pp. 469–. ISBN 978-1-4833-4651-9.
  3. Solomon, Brian. American Diesel Locomotives. Voyageur Press. p. 37. ISBN 9781610606059.
  4. "#1528 New York Central (Specification Photo Card)". eBay. Retrieved 2016-06-12.

External links

This article is issued from Wikipedia - version of the 11/2/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.