Harmony (ISS module)

Node 2 shown connected to Columbus, JEM, PMA-2 and Destiny. The nadir and zenith locations are open.

Harmony, also known as Node 2, is the "utility hub" of the International Space Station. The hub contains four racks that provide electrical power, plus electronic data, and act as a central connecting point for several other components via its six Common Berthing Mechanisms (CBMs). Harmony added 2,666 cubic feet (75.5 m3) to the station's living volume, an increase of almost 20 percent, from 15,000 cu ft (420 m3) to 17,666 cu ft (500.2 m3) The successful installation of Harmony meant that from NASA's perspective, the station was "U.S. Core Complete". Harmony was successfully launched into space aboard Space Shuttle flight STS-120 on October 23, 2007.[1][2] After temporarily being attached to the port side of the Unity node,[3][4] it was moved to its permanent location on the forward end of the Destiny laboratory on November 14, 2007.[5]

Origin of name

Interior of Harmony.

The unit formerly known as Node 2 was renamed Harmony in March 2007.[6] The name was chosen from a competition involving more than 2,200 kindergarten through high school students from 32 US states.[7][8] The Node 2 Challenge required students to learn about the space station, build a scale model, and write an essay explaining their proposed name for the module, which will serve as a central hub for science labs.

Specifications

Crew members hanging out of the USOS crew quarters
Harmony under assembly.

Weighing approximately 14,288 kilograms (31,500 lb), Harmony is the second of three node module on USOS.[7] The design is based on the existing Multi-Purpose Logistics Module, as well as the European Space Agency's Columbus Module.[7] There are six Common Berthing Mechanisms (CBMs) on Harmony, the one that connects it to Destiny is passive, the rest are active.[9] Harmony is managed by NASA's Marshall Space Flight Center in Huntsville, Alabama. Its deployment expanded the Space Station, allowing it to grow from the size of a three-bedroom house, to the space equivalent of a typical five-bedroom house, once the Japanese Kibō and European Columbus laboratories are attached. The Space Station robotic arm, Canadarm2, is able to operate from a powered grapple fixture fixture on the exterior of Harmony.[10] After the cancellation of the Habitation Module, Harmony was chosen to house the American Crew Quarters.[11][12] The first two were delivered on STS-126 and the second two on STS-128.[13][14]

The node measures 7.2 metres (24 ft) in length, and it has a diameter of 4.4 metres (14 ft).

Construction agreement

In an agreement between NASA and the European Space Agency the Rome-based company Thales Alenia Space built Harmony at its facility in Turin, Italy.[10] Harmony arrived on June 1, 2003 at the Kennedy Space Center in Florida after its flight in an Airbus Beluga oversize cargo vehicle. Following post transportation inspection, the Italian Space Agency formally handed over Harmony to the European Space Agency (ESA). From there, ESA formally transferred ownership of Harmony to NASA on June 18, 2003, taking place in the Space Station Processing Facility of the Kennedy Space Center.[15] The handover of Harmony completed a major element of the barter agreement, between ESA and NASA, that was signed in Turin on October 8, 1997.[15]

Paolo A. Nespoli, an ESA astronaut born in Milan, Italy, accompanied the Harmony module aboard STS-120 as a mission specialist.

Launch

Graphic showing the six CBMs on Harmony.

Harmony was launched October 23, 2007 aboard STS-120, as the primary component of assembly mission ISS-10A.[16][17][18]

On October 26, the station's Space Station Remote Manipulator System (SSRMS) removed Harmony from the shuttle cargo bay and temporarily mated it to the port side of Unity and, on October 27, the crew entered Harmony.[3][19] After the Space Shuttle departed Harmony was relocated to the forward dock of the Destiny laboratory. It required three EVAs by the station crew to complete the installation.[19][20]

Connecting modules and visiting vehicles

Harmony inside the payload bay of Space Shuttle Discovery while on its way to the ISS.

Harmony was the first permanent living space enlargement to the ISS after the Pirs docking compartment was added in 2001. The Expedition 16 crew moved the Pressurized Mating Adapter (PMA-2) on November 12, 2007 from the Destiny Laboratory to the forward berth of Harmony. The combined PMA-2/Harmony unit was subsequently berthed to its final destination at the forward end of the Destiny Laboratory on November 14, 2007.[5] All the following Space Shuttle missions would be docked to this location. On February 11, 2008, ESA's Columbus laboratory was attached to the starboard hatch of the Harmony module during space shuttle mission STS-122. On March 14, 2008 the Experiment Logistics Module Pressurized Section (ELM-PS) of Kibō was attached to its interim location: the zenith hatch of Harmony. During STS-124 a Space Shuttle mission flown by Space Shuttle Discovery, the Pressurized Module of Kibō was added to the port side of Harmony and the ELM-PS was moved, leaving the zenith hatch empty. The zenith hatch was originally intended to be the permanent docking connector for the now canceled Centrifuge Accommodations Module (CAM).

When the Space Shuttle flew the Multi-Purpose Logistics Modules (MPLMs) to the station, the MPLM would be temporarily berthed to the nadir mechanism of Harmony.[21] The Japanese H-II Transfer Vehicle and the American Commercial Resupply Service vehicles, Dragon and Cygnus, are temporarily berthed to either the nadir or zenith mechanism.

References

  1. ↑ NASA (October 23, 2007). "STS-120 MCC Status Report #01". NASA.
  2. ↑ John Johnson Jr. (October 24, 2007). "Space Shuttle Discovery lifts off". Los Angeles Times. Retrieved October 23, 2007.
  3. 1 2 William Harwood (2007). "Harmony module pulled from cargo bay". CBS News. Retrieved October 26, 2007.
  4. ↑ John Schwartz (October 26, 2007). "New Room Added to Space Station". The New York Times. Retrieved October 26, 2007.
  5. 1 2 NASA (2007). "PMA-3 Relocation". NASA. Retrieved September 28, 2007.
  6. ↑ NASA (2007). "NASA Space Station Module In Perfect 'Harmony' With New Name". National Aeronautics and Space Administration. Retrieved September 28, 2007.
  7. 1 2 3 European Space Agency (2007). "Node 2: Connecting Module". European Space Agency. Retrieved September 28, 2007.
  8. ↑ Tariq Malik (2007). "Students Name Next U.S. Space Station Module 'Harmony'". SPACE.com. Retrieved September 28, 2007.
  9. ↑ "ISS Interface Mechanisms and their Heritage" (pdf). NASA. p. 23. Retrieved November 4, 2011.
  10. 1 2 NASA (2007). "Space Station Assembly: Harmony Node 2". NASA. Retrieved September 28, 2007.
  11. ↑ "At Home with Commander Scott Kelly (Video)". International Space Station: NASA. December 6, 2010. Retrieved May 8, 2011.
  12. ↑ James Lee Broyan, Melissa Ann Borrego, and Juergen F. Bahr (2008). "International Space Station USOS Crew Quarters Development" (PDF). SAE International. Retrieved May 8, 2011.
  13. ↑ "STS-126 Press Kit" (PDF). NASA. November 2008. Retrieved September 26, 2011.
  14. ↑ "STS-128 Press Kit" (PDF). NASA. August 2009. Retrieved September 26, 2011.
  15. 1 2 European Space Agency. (2003). "European Node officially handed to NASA". ESA. Retrieved September 28, 2007.
  16. ↑ NASA (2007). "STS-120 to Deliver Harmony Node to ISS". NASA. Retrieved September 28, 2007.
  17. ↑ NASA (2007). "STS-120 Bringing Space Station 'Harmony'". NASA. Retrieved September 28, 2007.
  18. ↑ NASA (2007). "Launch Schedule: Consolidated Launch Manifest". NASA. Retrieved September 28, 2007.
  19. 1 2 William Harwood for CBS News (2007). "Astronauts enter Harmony". Spaceflight Now. Retrieved October 27, 2007.
  20. ↑ Victor Amateur Radio Association (2007). "Upcoming Shuttle Missions and ARISS Operations". Victor Amateur Radio Association. Retrieved September 28, 2007.
  21. ↑ SpaceRef.com (2007). "Space Station User's Guide: ISS Elements: Node 2". SpaceRef.com. Retrieved September 28, 2007.
Wikimedia Commons has media related to Harmony (module).
This article is issued from Wikipedia - version of the 12/4/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.