AMC Ambassador

AMC Ambassador
1958 Ambassador hardtop station wagon
Overview
Manufacturer	American Motors Corporation (AMC)
Also called	Ambassador by Rambler American Motors Ambassador [1] Rambler Ambassador IKA Ambassador
Production	1957–1974
Model years	1958–1974
Assembly	Kenosha Factory, Kenosha, Wisconsin, U.S. Australia (AMI)[2] Córdoba, Argentina (IKA) Costa Rica (ECASA)[3]
Body and chassis
Class	Mid-size/Full-size
Layout	FR layout
Chronology
Predecessor	Nash Ambassador

The Ambassador was the top-of-the-line automobile produced by the American Motors Corporation (AMC) from 1958 until 1974. The vehicle was known as the AMC Ambassador, Ambassador V-8 by Rambler, and Rambler Ambassador at various times during its tenure in production. Previously, the name Ambassador had applied to Nash's "senior" full-size cars.

The Ambassador nameplate was used continuously from 1927 until 1974 (the name being a top-level trim line between 1927 and 1931); at the time it was discontinued, Ambassador was the longest continuously used nameplate in automotive history.

Most Ambassador models were built in Kenosha, Wisconsin. They were also built at AMC's Brampton Assembly in Brampton, Ontario from 1963 to 1966. Australian Motor Industries (AMI) assembled Ambassadors from knock-down kits with right-hand drive. The U.S. fifth generation Ambassadors were produced by Industrias Kaiser Argentina (IKA) in Córdoba, Argentina from 1965 to 1972, as well as assembled by ECASA in Costa Rica from 1965 to 1970. Fifth and seventh generation Ambassadors were modified into custom stretch limousines in Argentina and the U.S.

Prologue

Following George W. Mason's unexpected death in the fall of 1954, George Romney (whom Mason had been grooming as his eventual successor), succeeded him as president and CEO of the newly formed American Motors. Romney recognized that to be successful in the postwar marketplace, an automobile manufacturer would have to be able to produce and sell cars in sufficient volume to amortize the high cost of tooling. Toward that end, he set out to increase AMC's market share with its Rambler models that were selling in market segment in which the domestic Big Three (General Motors, Ford Motor Company, and Chrysler) automakers did not yet compete. While development of a redesigned 1958 Nash Ambassador, based on a stretched and reskinned 1956 Rambler body, was almost complete, AMC's designers were also working on a retrimmed Hudson equivalent, called Rebel, to offer Hudson dealers.

However, as sales of the large-sized Nash Ambassador and Hudson Hornet models slowed, it became clear to Romney that consumer confidence in the historic Nash and Hudson nameplates had collapsed. Reluctantly, he decided that 1957 would be the end of both nameplates, and the company would concentrate on the new Rambler line, which was registered as a separate marque for 1957.

First generation

First generation
1958 Ambassador V8, Custom sedan
Overview
Also called	Ambassador V8 by Rambler
Model years	1958–1959
Body and chassis
Body style	4-door sedan 4-door hardtop sedan 4-door station wagon 4-door hardtop station wagon
Powertrain
Engine	327 cu in (5.4 L) V8
Transmission	3-speed automatic
Dimensions
Wheelbase	117 in (2,972 mm)

1958

American Motors planned to produce a stretched a 117-inch (2,972 mm) wheelbase version of the Rambler platform for Nash dealers to be the new Nash Ambassador, and another for Hudson dealers. Shortly before committing to production of the new long-wheelbase versions of the Hudson and the Nash, CEO Romney decided to abandon the Nash and Hudson marques.

Despite the fact that the Nash and Hudson names were canceled, work on the car itself continued, and American Motors introduced debuted in the fall of 1957, the 1958 "Ambassador V-8 by Rambler" on a 117-inch (2,972 mm) wheelbase. Its features included a 327 cu in (5.4 L) V8 (equipped with a 4-barrel carburetor and dual exhausts and rated at 270 hp (201 kW; 274 PS) and 360 pound force-feet (490 N·m) of torque) mated to a BorgWarner supplied 3-speed automatic transmission with push button gear selection.

In 1956, AMC first produced its own V8, a modern overhead valve V8 displacing 250 cu in (4.1 L), with a forged steel crank shaft, which when equipped with a 4-barrel carburetor was rated at 215 hp (160 kW; 218 PS). In 1957, AMC bored and stroked the 250 CID V8 to 327 cu in (5.4 L) displacement which when offered in the Rambler Rebel used solid lifters and Bendix electronic fuel injection was rated at 288 hp (215 kW; 292 PS).

In 1958, the Ambassador was equipped with a hydraulic lifter version of AMC's 327 CID V8 rated at 270 hp (201 kW; 274 PS). Although AMC's 327 CID V8 shares its displacement with the Chevrolet small-block, AMC's 327 came out six years before Chevrolet first offered its 327 in 1962.

The Ambassador was available in a body style exclusive to its line, a pillarless hardtop Cross Country station wagon. The 1958 Ambassador was offered in a single high level trim level and came equipped with such luxury items as electric clock, twin front and rear ashtrays, Nash tradition "deep coil" spring suspension front and rear, split back reclining front seats that fold down into a bed, as well as upscale fabrics for the interior.^[4]

Management had found that the public associated the Rambler name with small economy cars, and did not want the upscale nature of the new Ambassador to be so closely associated with Rambler's favorable, but economical image. Therefore, a decision was made that the larger Ambassador would be marketed as the Ambassador V-8 by Rambler in order to identify it with the Rambler name's burgeoning success, but to indicate an air of exclusivity by showing it to be a different kind of vehicle. However, the car wore "Rambler Ambassador" badges on its front fenders.

The 1958 Ambassador is a substantially longer car than the 108-inch (2,743 mm) wheelbase Rambler Six and Rebel V8, although both lines shared the same basic body, styling, and visual cues. However, all of the Ambassador's extra nine inches (230 mm) of wheelbase (and, therefore, overall length) were added ahead of the cowl, meaning that the passenger compartment had the same volume as the smaller Ramblers. The Ambassadors came with plusher interior and exterior trims while the front end incorporated the Rebel "V-Line" grille from the prototype Hudson model. Through effective market segmentation, the Ambassador was positioned to compete with the larger models offered by other automakers.

Model identification was located on the car's front fenders and deck lid. Super trim level Ambassadors featured painted side trim in a color that complemented the body color; Custom models featured a silver anodized aluminum panel on sedans and vinyl woodgrain decals on station wagons. Ambassador body styles included a four-door sedan and a hardtop sedan, a four-door pillared station wagon, and the aforementioned hardtop station wagon, a body style that first saw duty as an industry first in the 1956 Nash and Hudson Rambler line, on which all of the 1958 Ramblers were based.

The Ambassador had an excellent power-to-weight ratio for its time and provided spirited performance with 0 to 60 mph (0 to 97 km/h) times of less than 10-seconds, and low 17-second times through a quarter-mile (402 m) dragstrip. It could be equipped with a limited slip differential,^[5] as well as power brakes, power steering, power windows, and air conditioning. Numerous safety features (such as deep-dished steering wheels and padded dash boards) came standard, while lap seat belts were optional.^[6]

1959

For 1959, the Ambassador received a revised grille, side trim, and redesigned rear door skins that swept into the tailfins instead of terminating at the C-pillar. Scotchlite reflectors were also added to the rear of the tailfins to increase visibility at night. Front and rear bumpers were over 20% thicker, and featured recessed center sections to protect license plates. Adjustable headrests were now available as an option for the front seats, an industry first. AMC touted the added comfort the headrests provided, as well as their potential for reducing whiplash injuries in the event of a rear-end collision. Other changes included the activation of the starter through the neutral pushbutton (on automatic transmission equipped cars), and the addition of an optional "Powr-Saver" engine fan, which featured a fluid-filled clutch for quieter high-speed operation.

The 1959 model year also saw the addition of an optional "Air-Coil Ride" air suspension system, utilizing air bags installed within the rear coil springs.^[7] An engine-driven compressor, reservoir, and ride-height control valve comprised the rest of the system, but as other automakers discovered, the troublesome nature of air-suspension outweighed its benefits. AMC discontinued the unpopular option at the end of the model year.

Ambassador sales improved considerably over 1958, reaching an output of 23,769; nearly half of which were Custom four-door sedans. Much rarer was the hardtop station wagon, of which only 578 were built.

Second generation

Second generation
1960 Ambassador V8 by Rambler
Overview
Also called	Rambler Ambassador
Model years	1960–1961
Body and chassis
Body style	4-door sedan 4-door hardtop sedan 4-door station wagon 4-door hardtop station wagon
Powertrain
Engine	327 cu in (5.4 L) V8
Dimensions
Wheelbase	117 in (2,972 mm)

1960

1960 saw the Ambassador lineup totally reskinned, wearing new fenders, hood, deck lid, door skins, roofline, grille, taillights, bumpers, windshield, and backlight. Significant were the lower hood line, lower windshield cowl, simplified side trim, egg crate grill, while the tailfins were reduced in height and were canted to either side making for a modern and integrated appearance. The overall effect was rather fresh, as the new roof had a lower, lighter look, to complement the lower fins and grille.

All Ambassadors came equipped with the American Motors 327 cu in (5.4 L) V8, but for the first time it was available in two versions. First was the original 270 hp (201 kW; 274 PS), 360 lb·ft (490 N·m) of torque, performance version equipped with the 4-barrel carburetor and a 9.7:1 compression ratio, which required premium fuel, and a second economy version running on regular gasoline making 250 hp (186 kW), 340 lb·ft (460 N·m) of torque, equipped with a 2-barrel carburetor and an 8.7:1 compression ratio.

Ambassadors now came with a unique compound curved windshield that cut into the roof. This improved visibility, did away with the “knee knocker” dogleg design of AMC's first generation wrap-around windshield, and resulted in an even stiffer unitized structure. The 1960 Ambassador had a low cowl which with the compound windshield afforded excellent visibility. The Ambassador was offered in higher end Custom or entry level Super trim levels. All 1960 Ambassadors came with a new instrument cluster under a padded cowl, as well as illuminated controls for lights, wipers, fan, and defrost functions. The 1960 Ambassadors continued with an enclosed drive shaft (torque tube) and coil springs at all four corners, although the suspension was revised resulting in better handling. The top-of-the-line Ambassador models came standard with individual "airliner" reclining front seats that now had even more luxurious fabrics than in previous years.

The Ambassador was the only American midsize, luxury high-performance car offered in 1960. The 1960 Ambassador came in 4-door sedan, 4-door pillarless hardtop, 4-door station wagon, and a 4-door pillarless (hardtop) station wagon. Equipped with the 270 horsepower 327 cu in V8, and the Borg Warner pushbutton-operated 3-speed planetary gear and torque converter automatic transmission, the Ambassadors reached 60 miles per hour (97 km/h) in just over 9 seconds and passed the quarter-mile in 17 seconds.

1961

The 1961 Ambassador continued the previous year's 117-inch (2,972 mm) basic unitized platform, but received an unusual new front-end styling that was overseen by AMC's in-house design department headed by Edmund Anderson. The new face consisted of a trapezoid grille and headlights that floated in a body-colored panel, while the front fenders arched downward and forward of the leading edge of the hood. Different from anything else on the market, AMC's marketing department promoted the look as "European." While the new look was meant to distinguish the Ambassador from the lower-priced Ramblers, it was neither a consumer success nor well received in the automotive press. Overall sales fell as the entire industry was experiencing a recession. The hardtop sedan and wagon models did not return for 1961.

Standard was the 250 hp (186 kW; 253 PS) 327 cu in (5.4 L) V8 with a synchromesh manual transmission. Optional was the 270 hp (201 kW; 274 PS) "power pack" version with dual exhaust system featuring new ceramic-coated mufflers guaranteed for the life of the car.^[8]

Third generation

Third generation
1962 Rambler Ambassador
Overview
Also called	Rambler Ambassador
Model years	1962
Body and chassis
Body style	2-door sedan 4-door sedan 4-door station wagon
Powertrain
Engine	327 cu in (5.4 L) V8
Dimensions
Wheelbase	108 in (2,743 mm)

1962

By the 1962 model year, the Ambassador's chassis was in its fifth season on the market. And while Rambler sales had been good enough for third place in industry sales (behind Chevrolet and Ford), AMC's management was working on a revolutionary and somewhat costly design set to debut for the 1963 model year. In the meantime, American Motors needed to save money, and since the Ambassador's sales had fallen in 1961, it was decided that the car would be downsized for 1962 to share its body, windshield and 108-inch (2,743 mm) wheelbase with its Classic line mate. Accordingly, the car was marketed as a Rambler Ambassador.

The 1962 Ambassador received a new front end that was very similar to the 1961–62 Classic's, but with a crosshatch design, recessed center section, and Ambassador lettering. New, rectangular taillights were seen at the ends of restyled rear fenders, which lost their fins entirely. Exterior trim was reshuffled, and a new 2-door pillared sedan debuted. A new '400' trim line was added at the top of the line, with Super and Custom models remaining. The Ambassador offered even more luxurious interiors, perhaps to make up for the fact that it now shared its wheelbase with the Rambler Classic. The 400 could be had with vinyl bucket seats, headrests, and color coordinated shag carpets.

The only available engine was AMC's 327 cu in (5.4 L) OHV V8, in either the regular fuel, 2-barrel carburetor and 8.7:1 compression ratio, 250 hp (186 kW; 253 PS) version or the premium gasoline, 4-barrel version with 9.7:1 compression ratio, 270 hp (201 kW; 274 PS) version. The 1962 Ambassador came with a dual chamber master brake cylinder that separated the front and rear brakes so that in the event of the failure of one chamber some braking function would remain. This design was offered by only a few cars at that time. The 1962 models were equipped with "Walker" (brand) flow-through mufflers. The 108-inch (2,743 mm) wheelbase 1962 Ambassador was lighter than its 117-inch (2,972 mm) wheelbase predecessors and when equipped with the 270 hp (201 kW; 274 PS) 327 cu in (5.4 L) V8, it was a spirited performer.

The 1962, 327 cu in (5.4 L) V8 Ambassador for the first time used the same 108-inch (2,743 mm) wheelbase structure as did the 1957 Rambler Rebel which was also equipped with an earlier solid lifter version of the AMC 327. The 1957 Rambler Rebel equipped with a 3-speed column mounted manual transmission, was the quickest 4-door sedan made in the United States, achieving 0 to 60 mph (0 to 97 km/h) acceleration in just over 7 seconds, making it faster than the Hemi Chrysler 300C, the DeSoto Adventurer, the Dodge D500, the Plymouth Fury, and the Chevrolet fuel-injected 283.^[9] The 1962 Ambassador was available with a 3-speed manual transmission and being basically the same vehicle, should also reach 60 mph about as quickly as did the 1957 Rambler Rebel.

Fourth generation

Fourth generation
1963 Rambler Ambassador 880 Sedan
Overview
Model years	1963–1964
Body and chassis
Body style	2-door coupe (1963) 4-door sedan 4-door station wagon 2-door hardtop (1964)
Powertrain
Engine	327 cu in (5.4 L) V8
Dimensions
Wheelbase	112 in (2,845 mm)
Length	188.8 in (4,796 mm)
Width	71.3 in (1,811 mm)
Height	55.3 in (1,405 mm)

1963

In 1962 Romney left AMC to run for Governor of Michigan, a position that he won. The automaker's new president, Roy Abernethy, who was responsible for the increasing sales under Romney, reacted to the mounting competition (in 1963 AMC built as many cars as they had in 1960, but overall total car sales had increased so much that it gave AMC only sixth place in production; the same output in 1960 had put them third) in a logical way: "Let's get rid of this Romney image."^[10]

A completely redesigned larger Rambler lineup appeared. The new cars continued the philosophy in building smaller cars than its larger "Big Three" competitors that also had a high degree of interchangeability in parts to keep tooling costs and production complexity to a minimum. The company, which pioneered "styling continuity", introduced all-new styling for the 1963 model year Ambassadors and claimed that these were "functional changes .... not change just for the sake of change."^[11] The Ambassadors featured a 4-inch (102 mm) longer wheelbase, but were 1.2-inch (30 mm) shorter due to reduced front and rear body overhangs, as well as a 3-inch (76 mm) drop in over-all height.

Designed by Richard A. Teague, the 1963 Ambassador's shape was much tighter, cleaner, and smoother, with almost all of its parts interchangeable between it and the new Classic.^[12] All Ambassadors used unitized structure instead of the more rattl-prone, traditional body-on-frame construction which was still the industry standard.^[13] In 1963, AMC's new 112 in (2,845 mm) wheelbase cars (Ambassadors and Classics) used a revolutionary method of unit construction which has since been almost universally adopted by automobile manufacturers. AMC Ambassador and Classics used outerpanels stamped from single sheet metal panels which included both door frames and outer rocker panels. This resulted in an extremely rigid and rattle-free structure, better fit of doors into frames, production cost savings and reduced noise, vibration and harshness. The "uniside" structure was superior to the conventional production methods in which multiple smaller pieces were welded together.^[14] There were 30% fewer parts and the result was greater structural rigidity, quieter car operation, and an over-all weight reduction of about 150 pounds (68 kilograms).^[11]

Curved side glass and push-button door handles were new and costly upgrades, but contributed to the new Rambler's handsome, elegant, and modern Mercedes-like bodyside styling, by adding greater elegance in detail. At the time, curved side glass was used only in much more expensive luxury cars, but increased interior room and visibility, as well as reducing wind noise and improved proportions and styling of the cars.^[13] The Ambassador also featured a squared-off Thunderbird-type roofline.^[11] The front end featured a forward-thrusting upper and lower ends with a vertical bar "electric shaver" chrome grille insert. The Ambassador's grille was differentiated from the Classic's grille by its use of the Ambassador name in script in the small horizontal bar between the upper and lower grille sections. Round quad headlights were slightly recessed in chrome bezels mounted side-by-side within the grille at its outermost edges. Overall, the new Ambassadors were described by the staff of Automotive Fleet magazine as "probably the finest looking cars ever produced by American Motors."^[11]

Ambassadors once again came in 2-door coupe, 4-door sedan, and 4-door wagon body styles, but new trim lines debuted. A "Mercedes-like three-number model designation was developed" with the 800 as the Ambassador's base line (replacing the previous year's Super model) for the police, taxi, and fleet market, a 880 model (in place of the Custom), and the up level 990 trim (replacing the previous 400 models).^[12]

The 1963 Ambassadors were offered only with the 327 cu in (5.4 L) V8, in either 250 hp (186 kW; 253 PS) 2-barrel or 270 hp (201 kW; 274 PS) 4-barrel versions. AMC's smaller 287 cu in (4.7 L) V8 engine was only offered in the Classic line. The automatic transmission was controlled by a steering column mounted lever, replacing the previous pushbutton system. Maintenance was reduced with service intervals of the front wheel bearings increased from 12,000–25,000 miles (19,312–40,234 kilometres), the recommended engine oil change was at 4,000 miles (6,437 kilometres), and all Ambassador models included an alternator and a electronic voltage regulator as standard equipment.^[11]

Sales were brisk, and the redesign was billed a success, with Motor Trend Magazine bestowing Car of the Year status on the entire 1963 Rambler line, including the Ambassador. The marketing formula for the Ambassador generated record sales for the model with buyers favoring more luxury and features as evidenced by the Ambassador 990 models outselling the 880 versions by nearly 2-to-1, while the base 800 model had a total of only 43 two-door sedans built.^[12] The automaker did not have the resources of GM, Ford, and Chrysler, nor the sales volume to spread out its new model tooling and advertising costs over large production volumes; however, Richard Teague "turned these economical cars into smooth, streamlined beauties with tons of options and V-8 pep."^[10][15]

1964

The 1964 model year introduced minor trim changes and new options. The "electric-shaver" grille on the 1963 model was replaced with a flush-mounted design, and the engine and transmission options were widened. A two-door hardtop body style called 990-H was added for the first time since 1957. Base 880 and the 880 models were dropped from the line.

The 1964 Ambassadors featured the 250 hp (186 kW; 253 PS) 2-barrel 327 cu in (5.4 L) V8 as standard, with the 4-barrel 270 hp (201 kW; 274 PS) version as optional. The automaker did not offer a 4-speed manual transmission to compete with the sporty mid-size V8 offerings from Ford or GM. Instead, AMC offered its innovative “Twin-Stick” manual transmission. The "Twin stick" option consisted a three-speed manual transmission, operated by one of the two console mounted "sticks" in conjunction with an overdrive unit that was controlled by the second "stick" in both 2nd and 3rd gears. This gave the driver the option of using five forward gears. One magazine noted the Twin-Stick, 270 hp (201 kW; 274 PS) Ambassador was heading for a sub 16-second quarter-mile when they blew up the clutch.

• 

  1964 Rambler Ambassador

• 

  1964 Rambler Ambassador

• 

  1964 Rambler Ambassador interior with "Twin-Stick" transmission

Fifth generation

Fifth generation
1965 Rambler Ambassador 990 2-door hardtop
Overview
Also called	Rambler Ambassador AMC Ambassador
Model years	1965–1966
Body and chassis
Body style	2-door sedan 4-door sedan 4-door station wagon 2-door hardtop 2-door convertible
Powertrain
Engine	232 cu in (3.8 L) I6 287 cu in (4.7 L) V8 327 cu in (5.4 L) V8
Transmission	3-speed manual 3-speed with overdrive "Twin-Stick" on console (1965) 4-speed manual (1966) 3-speed automatic 3-speed “Shift-Command” on console
Dimensions
Wheelbase	116 in (2,946 mm)
Length	200 in (5,080 mm)

1965

No matter how much success the new Ramblers achieved in the marketplace, Roy Abernethy was not completely satisfied. Using the experience he gained as an outstanding salesman as a guide, Abernethy closely looked at the direction that American Motors' competition was going and decided that the company would be much more successful if its products competed more directly with the Big Three. He would achieve this by pushing all AMC vehicles further upmarket among the various market segments, shaking off the company's economy car image, and offering vehicles once again in all three major American car size classes: compact, intermediate, and full-size. The American and Classic were strong competitors in the former two segments, so for the 1965 model year, he set his sights on turning the Ambassador into a proper full-size car by stretching the Classic's wheelbase and giving it much different styling. The general sizes of automobiles at that time were based on industry standard wheelbase lengths, rather than on the vehicle's interior and cargo space. The 1965 Ambassador represented a fundamental shift in corporate ideology, a shift away from primarily fuel-efficient vehicles, to bigger, faster, and potentially more profitable cars.^[16]

Although the Ambassador rode the same platform as its 1963–64 forebears, the 1965 models looked all-new. American Motors' designer Richard A. Teague styled the 1965 Ambassador with panache and gave the car an overall integrated look.^[17] Motor Trend magazine agreed, calling it a "strikingly handsome automobile."^[18] Built on a 116-inch (2,946 mm) wheelbase four inches (100 mm) longer than the Classic, Teague extended the beltline level from the stacked quad headlights to the vertical taillights. The new Ambassadors were as attractive as anything built by AMC's Detroit-based competitors, and with a list price of around $3,000, few could quibble about the cost of ownership.^[16] New disc brakes with a power brakes were optional.^[19]

The Ambassador received longer, squared-off rear fenders with vertical wrap-around taillights, taller decklid, squared off rear bumper mounted low, and squarer rear wheel arches. At the front, the Ambassador again sparked minor controversy with its new vertically stacked quad headlights, which were slightly recessed in their bezels, as they flanked an all-new horizontal bar grille. This new wall-to-wall grille projected forward, horizontally, in the center, to create an effect somewhat opposite to 1963's grille treatment. The front end design provided a bold, rugged appearance.^[17]

Once again, the Ambassador’s entire extra wheelbase was ahead of the cowl, meaning that interior volume was the same as the intermediate-sized Classic. Another new body style debuted in the Ambassador lineup for 1965: an attractive new convertible offered as part of the 990 series. This was the first time a convertible was offered in the Ambassador line since 1948. All Ambassador body styles (except the 990-H coupe) offered seating for six passengers, with coupes and convertibles having the option of buckets seats with center console and floor shifter. The Ambassador 990-H was an up-scale two-door hardtop model, available only in 5-passenger form.

Ambassadors also saw an expanded list of trim lines, convenience options, and engine choices. The 990 and 990-H models were back, while 880 models were the new economy leaders in the 1965 Ambassador line, but even the $2,512 price for the two-door sedan was not attractive compared to the models with better trim, buckets seats, and special interiors.^[20] Ambassadors came standard with AMC's new 232 cu in (3.8 L) Inline-6 engine, which was the first time since 1956 that an Ambassador was available with six cylinders. Far more popular in the Ambassador, however, were the two time-tested 287 and 327 cu in (4.7 and 5.4 L) AMC V8 engines.^[21]

American Motors' management decided that the Ambassador could once again accept a standard six-cylinder engine, since its full-size competitors (e. g. Bel Air and Impala, Ford Custom 500 and Galaxie, as well as Plymouth Fury) came with six-cylinder engines as standard equipment. They therefore appealed to a wider range of customers than the Ambassador was getting. Also, since the Classic was now smaller and styled differently, the Ambassador six-cylinder would not threaten to cannibalize Classic 6 sales, which were the company's sales volume leaders. The changes were on target as sales of the repositioned Ambassador more than tripled.

Motor Trend magazine tested an Ambassador convertible with a Twin-Stick overdrive transmission and found it commendably economical, averaging 16.4 mpg_-US (14.3 L/100 km; 19.7 mpg_-imp) over 1,000 miles (1,600 km) run, and noting that ... "Traveling comfort was the Ambassador's biggest selling point, along with its exceptionally powerful Bendix duo-servo drum brakes ...With the thin bucket seats that recline, driver and passengers can enjoy a high degree of riding comfort... Many passers-by commented on the car's good looks... Our summary: a nice, comfortable, quiet, well built family automobile that rather neglects the performance market."^[22]

1966

For 1966, minor changes greeted the Ambassador range. The V-shaped horizontal louver spanned unbroken between the headlamps and the effect was continued with twin rectangular trim pieces attached to the side of the front fenders at their leading edges by the headlamps. The effect was repeated in the new vertical wraparound taillamps with the top-line models receiving a twin set of horizontal ribbed moldings across the back of the trunk lid that simulated the look of the front grille. Hardtop coupes received a redesigned roofline that was angular in appearance with an angle cut rear side windows and rectangular rear window. The backlight no longer curved and wrapped slightly around the C-pillars. The changes made for a more "formal" notchback look that was popular at the time.

Station wagons also received a new roof (that did not have as pronounced dip over the rear cargo area) as well as a redesigned tailgate and optional simulated woodgrain exterior side panels. Available with two-rows of seats with a standard bottom hinged tailgate with electric, fully retracting rear window or with an optional rear-facing third row that featured a left side hinged rear door, with a regular exterior door handle on the right side. All station wagons carried a Cross Country badge.

The 880 served as the base model line. The two-door sedan was the price leader at $2,404, but finished with the least sales for the model year.^[23] The more popular and better trimmed 990 models were available in sedan, wagon, hardtop, and convertible versions.^[23] Options included a vinyl roof, wire wheel covers, AM/FM radio, adjustable steering wheel, and cruise control. A new luxury DPL (short for "Diplomat"^[22]) two-door hardtop debuted at the top of the range.

The DPL included special lower body side trim, numerous standard convenience items such as reclining bucket seats upholstered in brocade fabrics or optional vinyl. An optional interior trim featured houndstooth fabric and included two throw pillows. The DPL model was aimed to compete with the new, more upscale trimmed Plymouth VIP, Ford LTD, Chevrolet Caprice and Oldsmobile Cutlass Supreme.^[24]

The 232 cu in (3.8 L) I6, as well as the 287 and 327 cu in (4.7 and 5.4 L) V8s remained in the line, but transmission selections now included a new console mounted four-speed manual. Most Ambassadors continued to be ordered with automatic transmissions.

Motor Trend magazine tested a 1966 DPL equipped with a 327 engine that "definitely has snap we hadn't felt before" and even with an automatic transmission experienced "healthy wheelspin from both rear wheels [because of the Twin-Grip limited slip differential]... Subtle changes in this year's suspension, which include longer shocks and different springs, have a pronounced effect on the way the car feels and handles. Most welcome is the improved steering response. The car has a new feet-on-the-ground feeling, and body lean seems to have been reduced. The ride remains very good... As before, the interior's the outstanding feature of the Ambassador. Its quality is such that other luxury cars, even higher priced ones, could well imitate it..."^[22]

Perhaps the biggest change, however, was that the Ambassador lost its historic Rambler nameplate, as the car was now marketed as the "American Motors Ambassador" or "AMC Ambassador". Abernethy was again responsible for this marketing move, as he attempted to move the stylish new Ambassador even further upmarket. To him, that meant that the Rambler name, and its economy car image would be eschewed to give the car a clean slate in a market that was turning away from economy and toward V8 performance. The evidence suggests that Abernethy was on the right track with moving the Ambassador upscale to compete with other manufacturers' luxury models as sales of the AMC's flagship jumped from 18,647 in 1964 to over 64,000 in 1965, and then in 1966 they went to more than 71,000.^[17] Although the Ambassador accounted for a mere fraction of total passenger car sales in the U.S., it was an important step in bringing the AMC's products in line with what the consumer of the day wanted.^[16]

Sixth generation

Sixth generation
1967 AMC Ambassador DPL convertible
Overview
Model years	1967–1968
Body and chassis
Body style	2-door sedan (automobile) (1967 only) 4-door sedan 4-door station wagon 2-door hardtop coupe 2-door convertible (1967 only)
Powertrain
Engine	232 cu in (3.8 L) I6 290 cu in (4.8 L) V8 343 cu in (5.6 L) V8 390 cu in (6.4 L) V8
Transmission	3-speed manual 3-speed with overdrive 4-speed manual 3-speed BorgWarner automatic 3-speed “Shift-Command” on center floor console
Dimensions
Wheelbase	118 in (2,997 mm)
Length	202.5 in (5,144 mm)

1967

American Motors introduced a completely restyled longer, lower, and wider Ambassador for the 1967 model year, now riding on a 118-inch (2,997 mm) wheelbase, or two inches (51 mm) longer than before. The Ambassador's platform was four inches (100 mm) longer than the new Rambler Rebel's 114-inch (2,896 mm) wheelbase. The Ambassador was positioned in the standard-size category, against traditional big cars such as Ford Galaxie, Chevrolet Impala, and Plymouth Fury.^[25] The convertible was offered again—this time in DPL trim—for 1967; but it would be the final year with only 1,260 built. It featured an all new "split stack" folding mechanism with concealed side rails that did not intrude into the backseat area, thus offering room for three adult passengers in the rear.^[26]

The car once again looked completely new, with a more rounded appearance that sported sweeping rooflines, "coke-bottle" fenders, greater glass area, and a recessed grille that bowed forward less than that of the 1965–66 models. Taillights were wider, rectangular, and divided by one central vertical bar. Motor Trend magazine described the all-new styling of the new Ambassador as “attractive” and “more graceful and easier on the eye in ’67.”^[27]

The 880 two-door sedans sported the identical roofline as the hardtops, but had slim B-pillars that gave them a more open-air coupe appearance. Adding more elegance to DPL two-door hardtops and convertibles was an optional was a "Satin-Chrome" finish (paint code P-42) for the lower body side replacing the standard full-length stainless steel rocker moldings. A black or white vinyl cover was optional on 990 and DPL sedans and hardtops. The 990 Cross Country station wagons were available with 3M's "dinoc" simulated wood-grain body side panels trimmed in a slim stainless steel frame.^[28]

The fastback Marlin two-door hardtop that was previously built on the Rambler Classic platform in 1965 and 1966, was continued for 1967, but was now based on the larger Ambassador platform. It featured the Ambassador's front end, longer hood, and luxury appointments with an even longer fastback roofline than the previous version.

The Ambassador featured a lengthy list of standard features and options. The interiors "rival more expensive cars for luxury and quality, yet are durable enough to take years of normal wear."^[27] The premium materials and fittings included wood-grain trim, and even an optional "Custom" package with special upholstery and two matching pillows. Ambassador DPL hardtops included reclining bucket seats with a center armrest between them (with a center cushion for a third occupant or a floor console with gear selector), as well as a foldaway center armrest for the rear seat. The new safety-oriented instrument panel grouped all gauges and controls in front of the driver, with the rest of the dashboard pushed forward and away from the passengers. Focusing on safety, there were now no protruding knobs, the steering column was designed to collapse under impact, and the steering wheel was smaller than previous Ambassadors.^[29]

AMC's long-lived "GEN-1" family of V8 engines was finally replaced by an all-new line of 290 and 343 cu in (4.8 and 5.6 L) engines debuted for 1966 in the Rambler American. With a 4-barrel carburetor and dual exhaust, the 343 V8 produced 280 bhp (210 kW) at 4800 rpm and 365 pound force-feet (495 N·m) of torque at 3000 rpm. The old torque tube design was eliminated by a new four-link, trailing-arm rear suspension system providing a more comfortable coil spring ride.^[30]

American Motors promoted the new 1967 Ambassador as an "uncompromising automobile with the red carpet ride" in print advertisements,^[31] as well as in an innovative TV commercial.^[32] Unfortunately, sales of the redesigned models were disappointing, due to customer confusion caused by the entire company's abrupt upmarket push, which seemed uncomfortably "me too" to the traditional domestic Big Three's customers, and they also alienated American Motors' loyal buyer base. Abernethy's ideas of entering new markets were not working.^[33] These strategy changes resulted in a new round of financial problems for American Motors. Because of this, Abernathy was released from AMC by its board of directors later that year, and was replaced by William V. Luneberg and Roy D. Chapin, Jr.

1968

For the 1968 model year, a new SST trim line was placed above the now mid-line DPL trim for the Ambassador. American Motors was a pioneer in the field of air conditioning through its Kelvinator refrigerator division, and AMC's marketing chief Bill McNealy wanted to make the Ambassador stand out in a crowded market segment and decided to add greater distinction to the Ambassador line by making the All Weather A/C system as standard equipment.^[34] This was the first time any volume car manufacturer had done so, something that even Cadillac and Lincoln had not offered on their luxury cars – although some of them were priced at more than twice as much as Ambassador. While all Ambassadors came with air conditioning as standard, consumers could order the car without air as a "delete option" and decrease the price by $218.^[35] As AMC pointed out in their advertising campaign for the Ambassador, the only other major automaker that offered air conditioning as standard equipment in 1968 was Rolls-Royce.^[36]

Due to slow sales, both the convertible and the pillared coupe models were dropped from the line, leaving the 990 hardtop coupe and sedan, DPL hardtop coupe, sedan, and wagon, and new SST hardtop coupe and sedan in the Ambassador line. The personal luxury fastback Marlin was also discontinued to make way for the smaller new AMC Javelin in the pony car segment. The top-of-the line 1968 Ambassador SST version was "especially appealing" and "a very luxurious package" with standard V8 power, air conditioning, expensive upholstery, individual reclining front seats, wood-look interior trim, upgraded exterior trim, as well as numerous conveniences such as an electric clock and a headlights-on buzzer.^[37]

Styling changes were minor. Taillights were now recessed in body-color bezels that were divided by a single central horizontal bar. Front headlight bezels were now made of nylon and similarly body colored.^[38] A new injection molded ABS plastic grille was dominated by a horizontal bar that extended forward in the center from the sides, while its outline had squared off edges that wrapped forward into the inner headlight extensions.^[38] Fender-mounted marker lights were added at the front and rear as standard equipment, as the U.S. National Highway Traffic Safety Administration (NHTSA) regulations mandated their application (along with seat belts beginning January 1, 1968) to all passenger cars sold in the United States for 1968.

However, AMC's most enduring styling feature debuted on the Ambassador for 1968, as flush-mounted paddle-style door handles replaced the former push-button units on all American Motors cars, save the Rambler American.^[38] The practical and "disarmingly simple design" predated safety-related mandates and industry norms.^[39] The interior locking was no longer by the traditional windowsill pushbutton, but a lever set into the armrest.^[39]

Front-wheel alignment was made easier with and with greater accuracy by moving the camber adjustment from the upper to the lower control arm on the double wishbone suspension, and the caster angle adjustments also moved from the upper control arm to the drag strut. At midyear, AMC's new top engine, the AMX 390 cu in (6.4 L) 315 hp (235 kW; 319 PS) V8 became an option in the Ambassador line, bringing the total engine options up to four.

In June 1967, American Motors started a new advertising campaign created by Mary Wells Lawrence of Wells, Rich, and Greene marketing agency. The US$12 million AMC account was high-profile assignment and helped established the agency as innovative and daring in its approach.^[40] The new advertising violated the convention of not attacking the competition, and AMC's campaigns became highly controversial.^[41] The publicity worked with AMC's total retail sales improving 13% for the fiscal year, but 1968 Ambassador numbers were slightly down.^[42]

Seventh generation

Seventh generation
1969 AMC Ambassador SST 4-door sedan
Overview
Also called	American Motors Ambassador [1] Rambler Ambassador [43]
Model years	1969–1973
Body and chassis
Class	Full-size
Body style	4-door sedan 4-door station wagon 2-door hardtop coupe
Powertrain
Engine	232 cu in (3.8 L) I6 258 cu in (4.2 L) I6 290 cu in (4.8 L) V8 304 cu in (5.0 L) V8 343 cu in (5.6 L) V8 360 cu in (5.9 L) V8 390 cu in (6.4 L) V8 401 cu in (6.6 L) V8
Dimensions
Wheelbase	122 in (3,099 mm)
Length	206.5 in (5,245 mm) (1969) 208 in (5,283 mm) (1970) 210.8 in (5,354 mm) (1971–72) 212.8 in (5,405 mm) (1973)

1969

In 1969, the Ambassador received a major restyling, with a 4-inch (102 mm) gain in overall length and wheelbase. The 122-inch (3,099 mm) wheelbase was accompanied by an increase in front and rear track from 58.5 to 60 inches (1,486 to 1,524 mm).^[44] The front end appearance was revised with new quad headlight clusters mounted horizontally in a new molded plastic grille. The grille itself was blackout with a chrome horizontal bar that connected the headlight clusters. The hood was redesigned to accommodate the grille's raised center portion, and it faintly recalled Packard's classic grille/hood combination. Richard A. Teague, AMC's Vice President of Styling, had worked at the luxury car manufacturer before joining AMC. Parking lights were rectangular and mounted horizontally in recessed wells in the front bumper, just beneath each set of headlights. The entire front fascia leaned forward slightly to lend an air of forward motion to the car's appearance.

At the rear, ribbed rectangular taillights were mounted inboard the Ambassadors rearward-thrusting rear fenders. Square ribbed marker lights of similar height were mounted at the trailing edge of each fender side. The deck lid had a slightly higher lift over. The base and DPL models had no decorative panel connecting the taillights while the top-line SST versions featured a panel painted red to match the taillights. Station wagons saw vertical wraparound taillights replacing the previous "hooded" units, which were not visible from the side. The 1969 AMC Ambassador was a smooth, powerful, well-proportioned sedan that did not look like anything else on the road.^[45]

The interiors were upgraded and a new deeply hooded dashboard clustered instruments and controls in front of the driver. There was an increased emphasis on luxury-type trim and features. The base model two-door hardtop was dropped for 1969.

The 1969 Ambassador stressed luxury, with the marketing tagline developed by Mary Wells Lawrence at the Wells Rich Greene agency, tying the car's value, "It will remind you of the days when money really bought something."^[46] The combination of rich velour upholstery, individually adjustable reclining seats, standard air conditioning, and the longer wheelbase were highlighted in advertisements with Ambassador's posh"limousine" ride at an economical price. One aspect of this new advertising theme included many AMC dealers inviting prospective customers to call and request a "demonstration ride", in which a uniformed chauffeur would arrive at the prospect's home and drive them around in an Ambassador SST sedan. AMC's efforts worked, and Ambassador sales shot up again.

Not only did AMC promote the 1969 Ambassador as having a "limousine" ride and deluxe appointments, but Chicago auto leasing executive, Robert Estes, had the Armbruster/Stageway Company^[47] convert Ambassadors into real 24-foot (7.3 m) limousines riding on a 158-inch (4,013 mm) wheelbase. Known as the Royale Stretch Limo, one was owned by the State of Wisconsin as the official vehicle for Governor Warren Knowles. The conversions were unusual in that they did not keep the stock rear doors—as is typical in most limos. The back doors were welded shut and the Ambassadors were lengthened by inserting a section just behind the original B-pillar that had an entirely new central door in this center making a large opening for entry and egress. Four-inch (100 mm) steel "I-beams" bridge the expanse created by stretch. Power comes from the "AMX" 315 hp (235 kW; 319 PS) 390 cu in (6.4 L) V8 engine backed with the BorgWarner automatic transmission and a "Twin-Grip" limited-slip differential with 3.15 gears.^[48]

American Motors exported Ambassadors from the United States, as well as assembled under license from complete knock down (CKD) kits. They were adapted to the requirements of different markets, including right-hand drive (RHD) versions.

1970

For the 1970 model year, the rear half of Ambassador hardtop coupes and sedans was treated to an overhaul that was also shared by the intermediate 1970 AMC Rebel. On hardtop coupes, this restyling resulted in a sloping roofline that saw upswept reverse-angle quarter windows. The belt line kicked up at the point the hardtop's rear windows swept upward, and tapered back to the fender end, meeting a new loop-type rear bumper.

On sedans, the roof line showed a slimmer "C-pillar", squared-off rear door windows, and met a belt line that kicked up beneath the trailing edge of each rear door window. The belt line tapered back to the same rear fascia as the hardtop coupe's. This rear fascia contained a new ribbed taillight lens that stretched wall-to-wall and included twin square white reverse light lenses in its center.

Station wagons received no change to their rooflines, doors, and rear fascias. However, all Ambassadors received a new extruded aluminum grille at the front, featuring several widely spaced bright horizontal bars with one wide, body colored horizontal grille bar extending to each headlight cluster. The 290 cu in (4.8 L) V8 was replaced for 1970 by a new 304 cu in (5.0 L) V8 engine. This 210 hp (157 kW; 213 PS) at 4400 rpm and 305 pound force-feet (414 N·m) of torque at 2800 rpm was the standard engine on all DPL and SST models. The 343 cu in (5.6 L) V8 was also supplanted by a 360 cu in (5.9 L) engine available in either 2-barrel, regular gasoline, or high-output, 4-barrel, premium fuel versions. The 4-barrel "AMX" 390 cu in (6.4 L) V8 engine was optional, producing 325 hp (242 kW; 330 PS) at 3200 rpm and 420 pound force-feet (569 N·m) of torque at 3200 rpm.

1971

Following the previous year's redesign, the 1971 Ambassadors received only minor changes and improvements. The marketing tag line for the year was the underdog asking, "If you had to compete with GM, Ford and Chrysler, what would you do?"—that was answered by AMC including more features, advantages, and benefits for buyers of its cars compared to the models from its much larger competitors. This was reflected by shuffling the Ambassador models for 1971 and by including more equipment in the standard feature list. The previously nameless base models were dropped, as the sedan-only DPL trim line was relegated to base model status, and a new top-line Brougham trim line was added above mid-line SST models. Both SST and Brougham models came as hardtop coupes, sedans, and wagons.

The DPL came with AMC's new 258 cu in (4.2 L) 150 hp (112 kW; 152 PS) Inline-6 with seven main bearings. All the SSTs and Broughams featured the 304 cu in (5.0 L) V8 engine with 210 hp (157 kW) as standard. BorgWarner's "Shift-Command" automatic transmissions were standard equipment across the line. Two of AMC's 360 cu in (5.9 L) were optional; an 8.5:1 compression version with a two-barrel carburetor or a high-compression four-barrel V8 that required premium-fuel. The previous "AMX 390" V8 gave way to a new 401 cu in (6.6 L) 335 hp (250 kW) V8 as the top engine option.

Styling changes consisted of a new fascia up front. It featured headlights contained in their own chrome pods separate from, but flanking the new grille with a bright rectangular surround, with rounded edges. The "natural" cast pot metal grille insert was recessed and featured a bright vertical bar pattern. A second set of parking lights was added outboard of the headlight clusters, and they were integrated into the fender extension to eliminate the need for separate front marker lights.

Taillights on hardtop coupes and sedans still ran wall-to-wall, but the twin backup lights were moved from the center to further outboard—approximately eight inches in from either fender side. Once again, the wagon received few changes at the rear, but added a new design for its optional woodgrain side trim, which filled in its upper bodysides. Its lower edge flowed downward aft of its peak at the leading edge above each front wheelhouse, in similar fashion to the Buick Skylark's side "sweepspear" styling cue.

Ambassador base models were offered to fleet buyers with various police, taxicab, and other heavy-duty packages. Governments and police departments in the U.S. historically used standard-size, low-price line four-door sedans. Equipped with the 360 or 401^[49][50] engines, the base Ambassadors saw use as police cruisers and support vehicles.

1972

Minor changes greeted 1972 Ambassadors, as AMC's biggest news for the year was the addition of the innovative AMC Buyer Protection Plan, that included the industry's first 12-month or 12,000-mile (19,000 km) bumper-to-bumper warranty.^[51] This was the first time an automaker promised to repair anything wrong with the car (except for tires) and owners were provided with a toll-free telephone number to the company, as well as a free loaner car if a warranty repair took overnight. This backing also included mechanical upgrades to increase durability and quality, such as the standardization of electric windshield wipers on all model lines, replacing AMC's vacuum-powered units, as well as better interior trims. By focusing on quality, the smallest domestic automaker was solidly profitable for 1972, earning US$30.2 million (the highest net profit achieved by AMC since 1964) on $4 billion in sales.

The base Ambassador DPL model was canceled, with three body styles now available in SST and Brougham trim. Fleet purchasers could order plain Ambassadors in Police Pursuit Vehicle (PPV) or Special Service Package (SSP) versions. A six-cylinder engine was no longer available; thus, Ambassador became a V8-only car for the first time since 1964. This made the Ambassador the only volume-produced American car that included air conditioning, power brakes, automatic transmission, and a V8 engine as standard equipment; all while being priced less than the Big Three's full-sized cars.^[52] The base engine was the 304 cu in (5.0 L) with two 360 cu in (5.9 L) or a 401 cu in (6.6 L) versions optional. The engines were designed to operate on regular grade, low-lead, or unleaded gasolines.^[53] All were based on the engine designs responsible for AMC winning the 1971–1972 Trans-Am Series.^[54] The Borg-Warner transmission was replaced by the "Torque-Command" (TorqueFlite) three-speed automatic sourced from Chrysler.

Styling changes on the 1972 Ambassador were limited to a new crosshatch cast metal grille with bright trim and new integrated fender extension mounted side marker lamps on the front. Brougham station wagons included a roof rack, rear air deflector, as well as 3M "dinoc" woodgrain trim on body sides and tailgate.^[52]

A Popular Mechanics magazine survey after driving a total of 1,000,000 miles (1,609,344 km) found Ambassador owners were pleased with their cars, describing them to be "very comfortable to drive and ride in" with handling listed as a top "specific like" by half of the drivers.^[55] A very high percentage (92%) would buy one again.^[55] Although the Buyer Protection Plan was listed by only 8.5% as a reason to buy an Ambassador, owners valued the smaller AMC dealers that "had more time to be courteous and to pay personal attention to customers."^[55]

1973

The SST models were dropped from the line, as all Ambassadors now came in one high-level Brougham trim. An AM radio and tinted glass were added to the extensive standard equipment list. Heftier front and rear bumpers were included to comply with new U.S. National Highway Traffic Safety Administration (NHTSA) regulations that required all passenger cars to withstand a 5-mile-per-hour (8 km/h) front and a 2.5-mile-per-hour (4 km/h) rear impacts without damage to the engine, lights, and safety equipment.

Ambassadors complied with the regulation by incorporating a stronger front bumper equipped with self-restoring telescoping shock-absorbers.^[56] Designed to "give" as much as 3.5 in (89 mm), it jutted slightly forward from the front fascia and incorporated flexible trim matching the body paint. This bumper also featured a more prominent horizontal rubber guard at its upper portion near the grille, thus eliminating the need for a pair of vertical chrome bumper guards that was optional before. The rear bumper gained vertical black rubber bumper guards that also replaced a pair of similar and previously optional chrome bumper guards. The grille gained heavier horizontal bars and headlight bezels took on blackout trim in their recessed portions.

Eighth generation

Eighth generation
1974 Ambassador Brougham sedan
Overview
Model years	1974
Body and chassis
Class	Full-size
Body style	4-door sedan 4-door station wagon
Powertrain
Engine	304 cu in (5.0 L) V8 360 cu in (5.9 L) V8 401 cu in (6.6 L) V8
Transmission	3-speed Torque Command automatic
Dimensions
Wheelbase	122 in (3,099 mm)
Length	217.8 in (5,532 mm)

1974

Ambassador sales had remained steady since 1970, despite the lack of major changes to the vehicle. However, the 1974 model year would bring out the biggest Ambassador—just as the 1973 Arab Oil Embargo sparked gasoline rationing across the nation. The Ambassador sedan was stretched seven inches (180 mm) compared with the 1973 versions. This additional length was due to a new front end design and stronger energy absorbing bumpers with hydraulic backup.^[57]

The 1974 Ambassador Brougham was no longer available as a 2-door (pillar-less) hardtop, leaving the 4-door sedan and station wagon body styles in the line. The hardtop's cancellation was due in part to low sales volume of the Ambassador 2-door versions, as well as the introduction of an all-new 1974 Matador coupe that featured a very long hood and a short rear deck. The new coupe was selected as the "Best Styled Car of 1974" by the editors of Car and Driver magazine and did not have the requisite share the typical mid- to late-1970s styling hallmarks that included an upright grille, a notchback roof, and imitation "landau bars" or opera lights.^[58] It was probably viable for AMC to build a "formal"-styled, personal luxury Ambassador version from the same platform.

Styling changes for the sedan and wagon included new front fender caps on the same fenders as used since 1969, and hood, grille, bumpers, rear fascia, instrument panel, interior trim, hood ornament, and a new font for the Ambassador nameplate. The grille showed off a new squared-off loop-type design surrounding the circular recessed quad headlights, and featured a forward-protruding center. The insert held a crosshatch pattern dominated by two thick horizontal bars that connected the headlight bezels and contained new parking lights between them. These parking lights had amber lenses, followed the grille protrusion forward, and were overlaid by the grille's crosshatch trim. Headlamp bezels were once again blacked out in their recessed areas. The new hood and front bumper followed the grille's central protrusion forward, giving the car a slight "coffin nose" look. The contemporary Matador saw a similar frontal treatment, but with a much more pronounced effect and with different single headlamp clusters, hood, and grille insert.

At the rear, the new bumper was much larger and backed by shock absorbers, as it was beefed up to comply with new National Highway Traffic Safety Administration regulations for standardized front and rear bumpers on passenger cars that could sustain a 5-mile-per-hour (8 km/h) impact with no damage. Fiberglass end caps were added to the ends of each rear fender on sedans. They wrapped inward to create a recessed space that met a carryover decklid. In this space was mounted the new rectangular taillight housings, which featured taller white backup lights mounted inboard of the new taillights. The license plate moved from the rear bumper to the area between the new taillight assemblies, and the whole taillight and license plate system on the sedans was surrounded its own loop of chrome trim.

The cargo area and the rear design of station wagons remained similar to previous Ambassadors, save for a massive new bumper and revised taillamps. The wagon was available with two-row bench seats for six passengers or with a rear-facing third row for a total eight seat-belted passengers. All came with numerous practical, appearance, and comfort items as standard. These included a two-way opening tail gate: (1) hinged at the bottom for convenient loading or hauling long cargo and (2) hinged at the side to open as door for ease of entry and exit for passengers or cargo; wood grained semi-transparent vinyl side and rear trim, a full-length roof rack; as well as a chrome and wood grain roof air deflector to help keep the tailgate window clean.

Powertrain selections remained the same as in 1973, with only V8 engines and automatic transmissions available. When ordered with a trailer package (special wiring harness with heavy-duty flasher and heavy-duty suspension with rear sway bar), the Ambassador was rated for up to 5,000-pound (2,268 kg) towing capacity.^[59] Other increases for 1974 included a larger capacity fuel tank, 24.9 US gal (94 L; 21 imp gal), and an alternator producing 62 amperes. New sound insulation made the Ambassador even quieter. All came with a very lengthy list of standard equipment that was typically optional on competing makes. These included comfort items such as air conditioning, an AM radio, and vanity mirror to appearance enhancements such as pin striping and whitewall tires.

Sales of all full-size vehicles, regardless of the automaker, fell significantly in 1974 as America's focus shifted to smaller cars. Ambassador sales were no different, and in June 1974, the final AMC Ambassador rolled off the Kenosha, Wisconsin assembly line, ending a nameplate that had been in continuous production in some form for 48 years.

Overseas production

Argentina

Industrias Kaiser Argentina (IKA) produced the U.S. third, fourth, and fifth generation Ambassadors in Córdoba, Argentina from 1962 to 1972, and later available by special order through 1975.^[60]

Assembly of IKA Ramblers began in 1962, with the Argentinean cars being the 1961 U.S. versions, but equipped with 226 cu in (3.70 L) Continental I6 engines producing 119 hp (89 kW; 121 PS) at 4000 rpm, along with a steering column mounted manual three-speed transmission. The Ambassador 440 was the top trim IKA model available only as a four-door sedan.

The completely new generation models by AMC in the U.S. for the 1963 model year was also replicated by IKA. The Ambassador sedan came only in 990 trim and it revolutionized the Argentine automotive market by introducing innovations that included power steering, power windows, and factory installed air conditioning.

The Ambassador line was redesigned for 1965 in the U.S., as well as for Argentina. All IKA Rambler models now featured the 230.5 cu in (3.78 L) overhead camshaft (OHC) straight-six "Tornado Interceptor" engines producing 145 hp (108 kW; 147 PS) at 4200 rpm. They were originally developed by Kaiser Motors in the U.S. for the 1963 Jeep Gladiator pickups and Wagoneer vehicles. The engine was now produced in Argentina and it increased the domestic (local sourced) content of IKA automobiles to lower taxes (tariffs).

The new IKA Ambassador 990 sedans were further upgraded to steering column mounted ZF four-speed manual transmissions, front disk brakes, front reclining bucket seats with center cushion and armrest, as well as the luxury features that included power windows and air conditioning.^[61] A road test by Revista Parabrisas described the 1965 IKA Rambler Ambassador 990 as "soft, opulent, and smooth ride at all speeds... something big, luxurious and complete... the highest expression of comfort tested so far by the magazine."^[62]

Stretch versions of the IKA Rambler Ambassador were used as official government limousines.^[63] The "Presidential" models featured longer a rear door and side window, as well as broader C-pillar with padded vinyl roof cover and a small rear window.

Australia

Australian Motor Industries (AMI) obtained the rights to assemble and distribute Ramblers, and the 1961, 1962, and 1963 model year Ambassadors were built in Australia.^[2] The 1961 sedan, which was powered by a 327 cu in (5.4 L) V8, was the most powerful car being assembled in Australia at that time.^[2] Knock-down kits featuring right-hand drive were shipped from Kenosha to AMI's facilities in Port Melbourne, Victoria. The Australian-built Ambassadors included a significant a percentage of "local content" to gain import tariff (tax) concessions by using parts and components (such as interiors and upholstery) that were sourced from Australian manufacturers. The dash and instrument pack of the 1967 Ambassador was converted to RHD by AMC and thereafter used in all Australian and New Zealand-assembled Rambler Rebel and Matador models, from 1967-1974.

Costa Rica

Rambler vehicles were marketed in Costa Rica since 1959.^[3][64] New local content regulations enacted during the 1960s effectively required vehicles sold in those markets to be assembled from knock-down kits.^[64] An assembly plant for Rambler and Toyota vehicles was established, ECASA, and the first Ramblers were produced in Costa Rica by the end of 1965.^[65] The company built Ambassadors and other AMC models through 1970, with Toyota increasing ownership of ECASA.^[3][66]

Epilogue

Because AMC was focusing its attentions on their newly acquired Jeep line, the redesigned 1974 Matador coupe, and the AMC Pacer, which would debut in 1975, the company would not put forth the investment to continue the full-size Ambassador line after its 1974 redesign. Instead, the automaker upgraded the Matador sedan and wagon counterparts starting with the 1975 model year. The basic automobile platform was used by AMC since the 1967 model year, and the full-size automobile market segment was declining. American Motors strategy now aimed at smaller cars and sport-utility vehicles. However, the Ambassador basically continued as the similarly sized and styled Matador sedans and wagons became available in uplevel "Brougham" trim from 1975, as well as in a unique top-of-the-line Barcelona trim in its final year of production, 1978.

Notes

References

External links

Wikimedia Commons has media related to AMC Ambassador.

• AMC Rambler Club
• American Motors Owners Association
• Nash Car Club
• Nash Healey History
• Nash in the UK
• 1967 Ambassador information
• Rambler Ambassador at the Internet Movie Cars Database
• AMC Ambassador at the Internet Movie Cars Database

American Motors (AMC) road car timeline, United States market, 1954–1987 Eagle »
Type	1950s						1960s										1970s										1980s
	4	5	6	7	8	9	0	1	2	3	4	5	6	7	8	9	0	1	2	3	4	5	6	7	8	9	0	1	2	3	4	5	6	7
Subcompact car	Metropolitan																									LeCar					Encore
																	Gremlin									Spirit
Compact car	Rambler				Rambler American												Hornet								Concord
	Jet																					Pacer								Alliance
Mid-size car			Six and V8		Six			Classic						Rebel				Matador										18i/Sportwagon						Medallion
				Rebel								Marlin									Matador Coupe
Full-size car	Nash Ambassador				Ambassador
	Hudson Hornet
	Hudson Wasp
Sports car/Roadster	N-H														AMX											AMX				Fuego				GTA
	Italia														Javelin
Crossover utility vehicle																											Eagle
SUV																	see early timeline of Jeep models										see late timeline of Jeep models
Military vehicles						Mighty Mite												AM General
Vehicle sold under Renault marque