AC Cobra

AC Cobra
AC Cobra MkIII
Overview
Manufacturer	AC Cars Shelby American[1][2][3]
Also called	Shelby AC Cobra[4] Shelby Cobra
Assembly	Thames Ditton, Surrey, England Los Angeles, California, USA
Body and chassis
Body style	2-door roadster
Layout	FR layout
Chronology
Predecessor	AC Ace
Successor	AC MK IV

MkI
CSX2000 – The first Cobra completed by Shelby
Overview
Production	1962–63
Powertrain
Engine	260 or 289 cu in (4.3 or 4.7 L) V8
Dimensions
Wheelbase	90 in (2,286 mm)
Length	151.5 in (3,848 mm)
Width	61 in (1,549 mm)
Height	49 in (1,245 mm)
Curb weight	2,019 lb (916 kg)[5]

MkII
MkII 289 (FIA Roadster)
Overview
Production	1963–65
Powertrain
Engine	289 cu in (4.7 L) V8
Dimensions
Wheelbase	90 in (2,286 mm)
Length	151.5 in (3,848 mm)
Width	61 in (1,549 mm)
Height	49 in (1,245 mm)
Curb weight	2,315 lb (1,050 kg)[6]

MkIII
1966 AC Cobra 427 (North America)
Overview
Production	1965–67
Powertrain
Engine	427 or 289 cu in (7.0 or 4.7 L) V8
Dimensions
Wheelbase	90 in (2,286 mm)
Length	156 in (3,962 mm)
Width	68 in (1,727 mm)
Height	48 in (1,219 mm)
Curb weight	2,355 lb (1,068 kg)[7]

The AC Cobra, sold as the Shelby AC Cobra and Shelby Cobra in the United States of America, is an Anglo-American sports car with a Ford V8 engine, produced intermittently in both the UK and United States of America since 1962.

History and development

Like many British manufacturers, AC Cars had been using the Bristol straight-6 engine in its small-volume production, including its AC Ace two-seater roadster. This had a hand-built body with a steel tube frame, and aluminium body panels that were made using English wheeling machines. The engine was a pre-World War II design by BMW which by the 1960s was considered dated. Bristol decided in 1961 to cease production of its engine and instead to use Chrysler 313 cu in (5.1 L) V8 engines. AC started using the 2.6 litre Ford Zephyr engine in its cars. In September 1961, American automotive designer Carroll Shelby wrote to AC asking if they would build him a car modified to accept a V8 engine. AC agreed, provided a suitable engine could be found. Shelby went to Chevrolet to see if they would provide him with engines, but not wanting to add competition to the Corvette they said no. However, Ford wanted a car that could compete with the Corvette and they happened to have a brand new engine which could be used in this endeavor: Ford's 260 in³ HiPo (4.2 L) engine – a new lightweight, thin-wall cast small-block V8 tuned for high performance. Ford provided Shelby with two engines. In January 1962 mechanics at AC Cars in Thames Ditton, Surrey fitted the prototype chassis CSX2000 with a 260 ci Ford V8 borrowed from Ford in the UK; the 221 ci was never sent. However, early engineering drawings were titled "AC Ace 3.6". After testing and modification, the engine and transmission were removed and the chassis was air-freighted to Shelby in Los Angeles on 2 February 1962.^[8] His team fitted it with an engine and transmission in less than eight hours at Dean Moon's shop in Santa Fe Springs, California, and began road-testing.^[9]

Production

Production proved to be easy, since AC had already made most of the modifications needed for the small-block V8 when they installed the 2.6 litre inline 6 Ford Zephyr engine, including the extensive rework of the AC Ace's front end bodywork. The most important modification was the fitting of a stronger rear differential to handle the increased engine power. A Salisbury 4HU unit with inboard disc brakes to reduce unsprung weight was chosen instead of the old E.N.V. unit. It was the same unit used on the Jaguar E-Type. On the production version, the inboard brakes were moved outboard to reduce cost. The only modification of the front end of the first Cobra from that of the AC Ace 2.6 was the steering box, which had to be moved outward to clear the wider V8 engine.

AC exported completed, painted and trimmed cars (less engine and gearbox) to Shelby who then finished the cars in his workshop in Los Angeles by installing the engine and gearbox and correcting any bodywork flaws caused by the car's passage by sea. A small number of cars were also completed on the East Coast of the USA by Ed Hugus in Pennsylvania, including the first production car; CSX2001.

The first 75 Cobra Mk1 models (including the prototype) were fitted with the 260 cu in (4.3 L).^[9] The remaining 51 Mk1 models were fitted with a larger version of the Windsor Ford engine, the 289 cu in (4.7 L) V8. In late 1962 Alan Turner, AC's chief engineer completed a major design change of the car's front end to accommodate rack and pinion steering while still using transverse leaf spring suspension. The new car entered production in early 1963 and was designated Mark II. The steering rack was borrowed from the MGB while the new steering column came from the VW Beetle. About 528 Mark II Cobras were produced in the summer of 1965 (the last US-bound Mark II was produced in November 1964).

Since late 1962 when the new GM Stingray was shown up briefly by the Mk1 Cobra (until hub failure intervened) the development of the Grand Sport Corvette program had continued at a pace and was thought to be going for a build series of 125 cars. This would allow GM to compete directly in the FIA GT class of racing. Just to compound this Enzo Ferrari was trying to pull another "fast one" on the FIA with the request for the homologation of the 250LM. The FIA had not forgotten the serious lack of production of the 250GTO, which it had granted homologation in advance of Enzo's assured 100 minimum per year. Just thirty-six were produced over three years with two very different chassis, neither of which were too similar to the 250 GT which was supposed to form the basis of the vehicle. In an effort to prepare for the task ahead alternative engines were considered. The 289 cu in (4.7 L) leaf-spring Cobra dominated the US domestic race series (USRRC), with only one race lost in three years. The results in the FIA GT class were different. This was mainly due to the number of circuits that had much higher sustained speeds. Aerodynamics were more important and put the roadster at a disadvantage. As a result, coupe versions were built.

A stroker 289 (325),and the larger 390/427 up to the "cammer" 427 was considered. Shelby was told at the eleventh hour to use the iron 427 cu in (7.0 L). There was little time to fully develop a competition vehicle. The coil spring Cobra production was slow and an insufficient number made to meet FIA's GT homologation. Therefore the S/C (Semi – Competition) was produced by making available to the general production the full race options for the street. By now Enzo was having races recategorised in Italy to prevent the almost inevitable defeat on home soil as the 250LM was not homologated as a GT and would have to run as a prototype. GM had pulled the plug on the Grand Sport and so the five chassis that were built had to run as prototypes and so were placed in a difficult position to say the least.

Shelby had earlier in 1964 fit a larger Ford FE engine of 390 cubic inches (6.4 L) in to CSX2196. Unfortunately the car was not able to receive the development it needed as resources were aimed at taking the crown from Ferrari in the GT class. Ken Miles drove and raced the FE-powered Mark II at Sebring and pronounced the car virtually undriveable, naming it "The Turd". It failed to finish with the engine expiring due to damper failure. A new chassis was required developed and designated Mark III. CSX2196 was revised for the show down at Nassau which allowed a more relaxed class division of racing. This allowed the GT cobras to run with prototype Ford GT, GM Grand Sport Corvettes and Lola Mk.6. The first meeting at which the GS Corvettes showed up was in 1963. It was for this event in 1964 that the Fliptop cobra was used. An aluminium 390 cubic inches (6.4 L) engine was used. However, the car failed to finish.

The new car was designed in cooperation with Ford in Detroit. A new chassis was built using 4 in (102 mm) main chassis tubes (up from 3 in (76 mm)) and coil spring suspension all around. The new car also had wide fenders and a larger radiator opening. It was powered by the "side oiler" Ford 427 engine (7.0 L) rated at 425 bhp (317 kW), which provided a top speed of 164 mph (262 km/h) in the standard model and 485 bhp (362 kW) with a top speed of 185 mph (298 km/h) in the competition model. Cobra Mark III production began on 1 January 1965; two prototypes had been sent to the United States in October 1964. Cars were sent to the US as unpainted rolling chassis, and they were finished in Shelby's workshop. Although an impressive automobile, the car was a financial failure and did not sell well. In fact to save cost, most AC Cobra 427s were actually fitted with Ford's 428 cubic inches (7.01 L) engine, a long stroke, smaller bore, lower cost engine, intended for road use rather than racing. It seems that a total of 300 Mark III cars were sent to Shelby in the USA during the years 1965 and 1966, including the competition version. 27 small block narrow fender versions, which were referred to as the AC 289, were sold in Europe. Unfortunately, The MK III missed homologation for the 1965 racing season and was not raced by the Shelby team. However, it was raced successfully by many privateers and went on to win races all the way into the 1970s. The remaining 31 unsold examples were detuned and fitted with wind screens for street use. Called S/C for semi-competition, an original example can currently sell for 1.5 million USD, making it one of the most valuable Cobra variants.^[10]

Cobra 289 Dragonsnake (CSX 2427) showing drag slicks at rear

Shelby wanted the AC Cobras to be "Corvette-Beaters" and at nearly 500 lb (227 kg) less than the Chevrolet Corvette, the lightweight roadster accomplished that goal at Riverside International Raceway on 2 February 1963. Driver Dave MacDonald piloted CSX2026 past a field of Corvettes, Jaguars, Porsches, and Maseratis and recorded the Cobra's historic first-ever victory. Later, Shelby offered a drag package, known as the Dragonsnake, which won several NHRA National events with Bruce Larson or Ed Hedrick at the wheel of CSX2093.^[11] Only five Dragonsnake Cobras were produced by the factory, with three others (such as CSX2093) prepared by customers using the drag package.^[12]

An AC Cobra Coupe was calculated to have done 186 mph (299 km/h) on the M1 motorway in 1964, driven by Jack Sears and Peter Bolton during shakedown tests prior to that year's Le Mans 24h race.^[13] A common misconception is that this incident persuaded the British Government to introduce the 70 mph (110 km/h) maximum speed limit on UK motorways, which up until that year had no speed restrictions, although government officials have cited the increasing accident death rate in the early 1960s as the principal motivation, the exploits of the AC Cars team merely highlighting the issue.

The AC Cobra was a financial failure that led Ford and Carroll Shelby to discontinue importing cars from England in 1967. AC Cars kept producing the coil-spring AC Roadster with narrow fenders, a small block Ford 289 and called the car the AC 289. It was built and sold in Europe until late 1969. AC also produced the AC 428 until 1973. The AC Frua was built on a stretched Cobra 427 MK III coil spring chassis using a very angular steel body designed and built by Pietro Frua. With the demise of the 428 and succeeding 3000ME, AC shut their doors in 1984 and sold the AC name to a Scottish company. The company's tooling, and eventually the right to use the name, were licensed by Autokraft, a Cobra parts reseller and replica car manufacturer owned by Brian A. Angliss.

Chassis numbering

The Ace chassis numbers read AEX... "A" being the car series and "X" being for export with left-hand drive. Later with the introduction of the Bristol engine the chassis numbers ran "BEX..." When switching to the Ford 2.6 engine the Ace chassis numbers ran "RS..." for Ruddspeed as Ken Rudd may have been influential in the choice of engine. The first Cobra chassis was left hand drive and given the next letter in the alphabet,i.e. C. Then "SX" for "Shelby eXport" i.e. exported to USA. Therefore the numbers ran CSX... for all the US export Cobras. The four following numbers ran from 2000 sequentially. When the MKIII Cobra was built the identification ran from CSX3000, the 3 signifying coil spring suspension. For the European market the cars were built wholly by AC cars in Thames Ditton using engines and transmissions imported from Ford USA. These cars were given chassis numbers beginning "COB...." for "Cobra Britain" i.e. RHD home market and "COX..." for "Cobra Export" i.e. RHD export other than to USA. COB/COX cars had chassis numbers beginning with a 6 and then either a 0 to signify a leaf sprung chassis or a 1 to signify a coil sprung chassis.

Autokraft era

Autokraft manufactured an AC 289 continuation car from 1982 as the Autokraft Mk IV, basically a Mk III with a 302 cubic inches (4.95 L) Ford V8 and Borg Warner T5 Transmission. The Mk IV also received an independent suspension. Shortly thereafter, Carroll Shelby filed suit against AC Cars and Brian A. Angliss, in U.S. District Court in Los Angeles. The ensuing settlement resulted in Shelby and AC Cars/Angliss releasing a joint press release whereby AC/Angliss acknowledged that Carroll Shelby was the manufacturer of record of all the 1960s AC Cobra automobiles in the United States and that Shelby himself is the sole person allowed to call his car a Cobra. Nonetheless, production of the Mk IV continued, from 1987 as a joint venture with Ford as the AC Mk IV with a 250 hp (186 kW) at 4,200 rpm, 4,942 cc Ford V8 which provided a top speed of 215 km/h (134 mph) and 0–100 km/h in 5.2 seconds. At the 1990 Geneva Salon the Lightweight version was presented: weight was down to 1,070 kg (2,360 lb) (compared to 1,190 kg or 2,620 lb) and power was up to 370 hp (276 kW) at 5,750 rpm thanks to alloy heads, a Holley four-barrel carburettor, and no catalytic converter.^[14] While the Lightweight did not meet US federal regulations, the Mk IV did, and 480 cars of all versions were built until 1996.

Post Autokraft era

Brian Angliss left AC Cars in 1996 and the company was restructured under new management. Two new 'Cobra' style cars were launched in 1997, the 'Superblower', an aluminium-bodied car with a supercharged 4,942cc Ford V8 providing 320 bhp and the cheaper 'Carbon Road Series' (CRS) with a carbonfibre body and a 225 bhp version of the Ford V8 engine. 22 Superblowers and 37 CRSs were built between 1997 and 2001.

A further variant, 'the 212 S/C' with a 3506 cc 350 hp twin-turbocharged Lotus V8 engine was introduced in 2000, but only two examples were built.

In 2006, AC closed its UK factory and moved to Malta. However only 3 right-hand drive carbon-fibre AC Mk Vs powered by 340 bhp 5-litre Ford V8 engines were built before the Maltese operation closed. Since 2009, AC has licensed Gullwing GmbH in Germany to produce the AC MK VI, with an aluminium coated composite body and powered by a 6.2 litre 440 hp LS3 Chevrolet engine, or a 550 hp supercharged version. In the UK, AC Heritage based at Brooklands, is licensed by AC to produce traditional 289 and 427 continuation ACs.

Coupé

1964 Shelby Daytona Cobra Coupe (CSX2299)

1965 Willment/Ghia Coupe (CSX3055)

In an effort to improve top speed along the legendary Mulsanne Straight at the 24 Hours of Le Mans race, a number of enclosed, coupe variations were constructed using the leafspring chassis and running gear of the AC/Shelby Cobra Mark II. The most famous and numerous of these were the official works Shelby Daytona Cobra Coupes. Six were constructed, each being subtly different from the rest. AC Cars also produced a Le Mans coupé. The car was a one-off and was nearly destroyed after a high-speed tire blow-out at the 1964 Le Mans race. The car was qualified conservatively second in GT. The race started well with the AC, chassis number A98, maintaining its position in the top two in GT and even leading the class for a time. This was not to last as an act of sabotage (newspaper in the fuel tank) began to block the fuel filter. The car lost time until this was diagnosed and cleaned out. The car proceeded on at the predetermined conservative lap time and for the next stint remained trouble free. The car was able to match the Shelby Daytona's speed despite running a higher differential ratio (2.88 instead of 3.07) and a lower state of engine tune for reliability (355 hp instead of the Daytona's 385 hp).

The third significant Cobra-based coupe was the Willment Cobra Coupe built by the JWA racing team.

A road-going Shelby Daytona Cobra replica is being manufactured by kit-car companies Superformance and Factory Five Racing. These cars use Pete Brock's bodywork designs, scaled up to increase room inside, and newly designed spaceframe chassis, they are powered by Roush-built Ford Windsor (Sportsman) engines. The Superformance Shelby Daytona Coupe is the only modern-day vehicle recognized by Shelby as a successor to the original Coupes.

Other road-going Shelby Daytona Cobra replicas include Daytona Sportscar from Australia.

Counterfeit Cobras

In 1993 the Los Angeles Times exposed a Carroll Shelby scheme^[15] to "Counterfeit" his own cars. With the price of an original 427 c.i. Cobra skyrocketing, Shelby had, by his own written declaration executed under penalty of perjury, caused the California Department of Motor Vehicles (the government agency responsible for titling vehicles and issuing operator permits) to utter forty-three "Duplicate Titles" for vehicles that did not officially exist in company records. A letter from AC Cars confirmed the fact that the chassis numbers Shelby had obtained titles for were never manufactured, at least by AC Cars. Only fifty-five 427 c.i. Cobras had been originally produced out of a block of serial numbers reserved for 100 vehicles. Shelby had taken advantage of a loophole in the California system that allowed one to obtain a duplicate title for a vehicle only on a written declaration, without the vehicle identification number appearing in the DMV's database or the declarant ever presenting an actual vehicle for inspection.^[16] Shelby later admitted^[16] that the chassis had been manufactured in 1991 and '92 by McCluskey Ltd, an engineering firm in Torrance, California, and were not authentic AC chassis.

Continuation cars

50th Anniversary Cobra Limited Edition CSX8000.

From the late 1980s onwards, Carroll Shelby (Shelby Automobiles, Inc.) and associated companies have built what are known in the hobby as "Continuation Cars"; Shelby authorized continuations of the original AC-built Cobra series. Produced in Las Vegas, Nevada, these cars retain the general style and appearance of their original 1960s ancestors, but are fitted with modern amenities. Initially the car everyone wanted in a Continuation was a 427 S/C model which was represented in the CSX4000 series. This was meant to continue where the last 427 S/C production left off, at approximately serial number CSX3560 in the 1960s.

The initial CSX4000 series cars were completed from the chassis built by McCluskey Ltd as well as other new parts and reconditioned Ford engines. Given the value of the vehicle many "extra" cars have appeared over the years, even some sharing the same chassis number. Gradually as the vintage parts supply ran low, newly constructed frames and body panels were obtained from a variety of suppliers. The production of chassis numbers CSX4001 to CSX4999 took roughly 20 years and many different business relationships to complete.

All models of Cobra produced are available now as continuations. In 2009, CSX4999 was produced, concluding the 4000 series. Production has continued with the CSX6000 serial numbers, featuring "coil over" suspension. The 289 FIA "leaf spring" race version of the car is reproduced as CSX7000, and the original "slab side" leaf spring street car is the CSX8000 series.

To date most continuations are produced in fiberglass, with some ordering cars with aluminium or carbon-fibre bodywork.

In 2004, at the North American International Auto Show in Detroit, Ford unveiled a concept for a modernized AC Cobra. The Ford Shelby Cobra Concept was a continuation of Ford's effort to bring back the retro sports cars that had been successful in the 1960s, including the Ford GT40 and the fifth generation Ford Mustang.

Cars were also produced by AC Cars until 2006, and since 2009 have been produced by AC Heritage, who are licensed by AC to produce 289 and 427 continuations.

In 2014 Shelby American announced a limited edition production of 50 cars for the 50th anniversary of the original 427 Shelby Cobra.^[2][17]

Super Snake

Competition 427, (CSX3009) "Ollie the Dragon"

AC produced only 23 AC Cobra 427 competition roadsters. In 1966, one was selected and converted into a special model called the Supersnake the "Cobra to End All Cobras." The first one of these was originally part of a European promotional tour before its conversion. This conversion called for making the original racing model street legal with mufflers, a windshield and bumpers amongst other modifications. But some things were not modified, including the racing rear end, brakes and headers. The most notable modification is the addition of Twin Paxton Superchargers, TPS. Shelby crafted two 427 models, adding the TPS to each, they were built from cars with the serial numbers CSX 3303 and CSX 3015. He gave one of the two cars, CSX 3303, to comedian Bill Cosby, a close friend, and kept CSX 3015 for himself. Shelby' car was converted from one of the 427 SC (Semi-Competition)Cobras. Cosby' car was a later street car converted to a Supersnake.

When Cosby attempted to drive his CSX3303, he found that it was very difficult to keep under control; he later recounted the experience on his 1968 stand-up comedy album 200 M.P.H.. Cosby gave the car back to Shelby, who then shipped it out to one of his company's dealers in San Francisco, S&C Ford on Van Ness Avenue. S&C Ford then sold it to customer Tony Maxey. Maxey, suffering the same issues as Cosby did with the car, had his throttle stick while leaving a traffic stop, lost control and drove it off a cliff, landing in the Pacific Ocean waters.^[18]

Shelby used his CSX 3015 as a personal car over the years, sometimes entering it into local races like the Turismos Visitadores Cannonball-Run race in Nevada, where he was "waking [up] whole towns, blowing out windows, throwing belts and catching fire a couple of times, but finishing."^[19] CSX3015 was auctioned on 22 January 2007, at the Barrett-Jackson Collector Car Event in Scottsdale, Arizona, for $5 million plus commission (£2.8 million), a record for a vehicle made in the U.S.^[20][21]

See also

• Bill Thomas Cheetah, the 1963-started, Chevrolet Corvette-based private-venture challenger to the Cobra
• The Snake and the Stallion

References

Notes

Bibliography

External links

Wikimedia Commons has media related to AC Cobra.

• AC Cobra at DMOZ
• AC Cobra at the Internet Movie Cars Database
• Shelby Automobiles Inc., Las Vegas, Nevada
• thecobraferrariwars.com
• AC Cars website
• AC Heritage website
• AC Cobra 427 (1969) Exterior and Interior in 3D 4K UHD
• International club for owners of original and replica 289 Cobras and Aces